Sie sind hier : Startseite →  Hifi Kataloge→  1962 der IMHOFS Hifi Katalog→  Imhofs Hifi Products 1962/2

Einblick in den Imhofs Hifi Katalog von 1962

Es ist etwas Besonderes, einen so gut erhaltenen Hifi-Katalog aus dem England von 1962 zu bekommen. Wir haben die Seiten so geschickt wie möglich aufgeteilt, sonst würde eine einzelne Seite zu lang werden. Blättern Sie oben in der weißen Leiste von Seite zu Seite.

Es sind alles noch Röhrenverstärker im Jahr 1962.

Ende 1962 haben die ersten Transistorverstärker die Labors verlassen und das Licht der Welt erblickt. Grundig war einer der Ersten, eigentlich der Erste mit einem wirklich fertigen Produkt, dem Grundig SV50. Doch ein Amerikaner war ein paar Monate schneller (mit einem Prototyp) und so konnte Grundig nicht mit "dem Allersten auf der Welt" werben. Er war "nur noch" der Erste in Europa. Sicher werkelten auch Quad und Rogers an solchen Geräten, doch es dauert noch.

-

choosing an amplifier (Anmerkung: es war 1962)

The choice of an amplifier is governed by considerations of cost, power and flexibility. As the amplifier is the heart of a hi-fi system it is well worth buying the best one can afford.

The main amplifier and the control unit or pre-amplifler may be bought as separate units or combined on one chassis; the term 'amplifier' used alone usually refers to the combination.
The control unit should have independent bass and treble controls, a selector for various types of records and inputs for radio and tape.

The provision of a filter is well worth while. In the main amplifier, wide frequency range alone is not enough; low distortion at full output is essential and the frequency range and distortion figures must be known for full output, not for some nominal figure. Except for the very smallest rooms, a 10 watt amplifier would be the minimum and 15 or 25 watts may not be excessive in a large room with relatively inefficient loudspeakers.

If the system is to be used for stereo listening then either two complete amplifiers or a double amplifier and stereo control will be necessary. If a system is to be used for single-channel reproduction at present but possibly to be converted to stereo later, choose units which may be converted without making any of the components redundant. Imhofs staff will always be happy to advise you of the most suitable unit for your requirements.

amplifiers list 1962 (mit Anmerkungen)

Im Imhof Katalog sind 1962 bereits 25 Röhren-Verstärker abgebildet und fast 30 beschrieben. Der "dickste" (Mono-) Verstärker ist der LEAK TL/50 mit 50 Watt Sinus an jeder Impedanz von 3 bis 20 Ohm. Alle anderen Verstärker haben mit bis zu 18 Watt deutlich weniger Sinusleistung. Der amerikanische McIntosh MC 275 mit seinen 2 x 75 Watt Sinus zum Beispiel ist hier gar nicht vertreten.

-

Acoustical Quad 22 Control Unit

Stereo unit: usable for single-channel if required. Valves: two EF86 (Z729 or 6267), two ECC83 (12AX7). Distortion: less than 0.1%. - Hum and noise: better than -70db. Input sensitivity (for 1.4V rms output): radio and tape 70 mV rms, mic. 1.5mV rms. Frequency response: ± 1.5db, 20 to 20,000 c/s. - Dimensions: 10"w x 6"d x 3'h. - Weight: 9lb. - There is also the single-channel Quad II control unit.

Acoustical Quad II Main Amplifier

Valves: two EF86 (Z729 or 6267); two KT66 (5883 or 6L6G matched); one GZ32 (54KU or 5V4G). Power output: 15 watts throughout the range 20-20.000 c/s. Distortion: at 12 watts output not to exceed 0.25% at 25 c/s. Background: 80db referred to 15 watts. Input sensitivity: 1.4V. rms for 15 watts output. Frequency response: within 0.2 db 20-20.000 c/s; within 0.5db 10-50.000 c/s. Output impedances: 15 ohms and 7 ohms. Power supply: 200-250 AC single phase (or 100-130 AC). Consumption: 90 watts (excl. control unit, tuners, etc.). Dimensions: 13w x 4"d x 6"h. Weight 18lb.

Armstrong PCU25 Stereo Control Unit

Valves: two EF86, three ECC83. Distortion: less than 0.1% for 410mV output. Dimensions: front panel 10" x 4"; chassis IV deep. Weight: 4lb.

Armstrong A20 Stereo Amplifier

Valves: GZ34, three ECC83, four EL84. Power output: 12 watts rms per channel (24 watts peak). Total harmonic distortion: less than 0.1% at 12 watts. Hum and noise: 85db below rated output. Frequency response: 15-22,000 c/s ± 1db. Damping factor: 53. Output impedance: 4, 8 or 16 ohms. Power supply: 100-250V AC. Dimensions: 14" x 7" x 7". Weight: 19 lb.

H.M.V. Model 555 Stereo Amplifier

Valves: two EF86, six ECC 83, four EL84. Power output: 10 watts rms. per channel (20 watts peak). Total harmonic distortion: 0.1% at 10 watts output at 1,000 c/s. Hum and noise: 80db below full output. Frequency: ± 1db 20 to 20,000 c/s. Damping factor: 30. Dimensions: 4" x 14" x 13" deep overall.

H.M.V. Model 556 Stereo Preamplifier

Basically the preamplifier section only of the Model 555. - Dimensions: 4" x 14" x 10" deep. Weight: 14lb.

H.M.V. 599 Stereo Amplifier

Valves: three ECC83, four EL84. Power output: 10 watts rms per channel (20 watts peak). Distortion: 0.1% for 10 watts at 1 K/cs. Hum and noise: 80db below full output.
Frequency response: 20-20,000 c/s ±1db. Damping factor: 30. Output impedances: 32,16, 8 or 4 ohms.
Power supply: 200-250V AC or 100-125V AC. Dimensions: 14" x 8" x 4".

Jason Amplifier Model J.10

Power output: 15 watts (peak). - Distortion: less than 0.1% at full output. Power response: 3db from 25-65,000 c/s.
Loudspeaker impedance: 15 ohms. Power supply: AC 200-250V, or 115V, 40-100 c/s. Dimensions: 11" wide x 6" deep x 4" high

Jason Stereo Amplifier J.2-10 Mk. Ill

Power output: 10 ± 10 watts (15 4- 15 watts peak). Distortion: less than 0.1% at full output. Frequency response: ± 0.5db 20-20,000 c/s. Loudspeaker impedances: two 15 Ohms; adaptor for twin 4 ohm speakers available. Power supply: 210, 230, 250V. AC or 105, 115, 130V AC. Dimensions: 15"w x 8"d x 4"h.

Leak "Point One Plus" Pre-Amplifier

Valves: two EF86 or Z729 or 6267. Total harmonic distortion: less than 0.1% for 1.25V output. Hum and noise: approximately 66db below full power output on radio and tape positions and approximately 60db below on other inputs. Dimensions: front panel 1H" x 4-jV'; chassis 10"w x 3d x 5h. Weight: 4 lb.

Leak "Varislope 111" Pre-Amplifier

Valves: two EF86 or Z729 or 6267. Total harmonic distortion: less than 0.1% for 1.25V output. Hum and noise: approximately 66db below full power output on radio and tape positions and approximately 60db below on other inputs. Dimensions: front panel 1H"x 4tV', chassis 10"w x 3d" x 5"h. Weight: 5 lb.

Leak "TL/12 Plus" Main Amplifier

Valves: one EF86 or Z729 or 6267, one ECC81 or B309 or 12AT7, two EL84 or N709 or 6BQ5, one GZ34 or 5V4 or 5AR4. Power output: 14 watts rms. maximum. Total harmonic distortion: 0.1% at 12 watts output (±1db) at 1,000 c/s. Hum and noise: 85db ± 3db, below 12 watts with a source impedance of 25,000 ohms. Sensitivity: an input of 125mV at 1,000 c/s gives 12 watts output.
Frequency response: ± 0.5db, 20-20,000 c/s. Damping factor: 25, measured at 1,000 c/s. Loudspeaker impedances: loudspeakers of any impedance between 3 ohms and 20 ohms may be used. Power supply: 200-250V 50-100 c/s or (alternative model), 100-125V 50-100 c/s. Consumption: 75 watts. Dimensions: 10" x 7" x 5". Weight: 14lb.

Leak "TL/25 Plus" Main Amplifier

Valves: one EF86 or Z729 or 6267, one ECC81 or B309 or 12AT7, two EL34 or KT66 or 5881, one GZ34 or 5V4 or 5AR4. Power output: 32 watts rms. maximum. Total harmonic distortion: 0.1 % for 25 watts output (± 1db) at 1,000 c/s. Hum and noise: 86db, ± 3db, below 25 watts with a source impedance of 25,000 ohms. Sensitivity: an input of 125mV at 1,000 c/s gives 25 watts output. Frequency response: ± 0.5db, 20-20,000 c/s. Damping factor: 25, measured at 1,000 c/s. Loudspeaker impedances: loudspeakers of any impedance between 3 ohms and 20 ohms may be used. Power supply: 200-250V, 50-100 c/s or, (alternative model) 100-125V, 50-100 c/s. Consumption: 130 watts (135 watts with Leak pre-amplifier). Dimensions: 10" x 7" x 6". Weight: 17 lb.

Leak "TL/50 Plus" Main Amplifier

Valves: one EF86 or Z729 or 6267, one ECC81 or B309 or 12AT7, two KT88 or 6550, one GZ34 or 5AR4. Power output: 50 watts rms. maximum. Total harmonic distortion: 0.1% for 50 watts output (± 1db) at 1,000 c/s. Hum and noise: 83db ± 3db below 50 watts with a source impedance of 25,000 ohms. Sensitivity: an input of 125mV at 1,000 c/s gives 50 watts output. Frequency response: ± 0.5db 20 c/s to 20,000 c/s. Damping factor: 15, measured at 1,000 c/s. Loudspeaker impedances: loudspeakers of any impedance between 3 ohms and 20 ohms may be used. Power supply: 200-250V, 50-100 c/s or 100-125V, 50-100 c/s. Consumption: 145 watts. Dimensions: 11" x 9" x 6". Weight : 28 lb.

Leak "Point One Stereo" Pre-amplifier

Balance control: dual ganged, permitting perfect channel balance and giving facilities of: (1) varying channel gains from zero to maximum to compensate for differences in loudspeaker sensitivities, and (2) monaural listening on either loudspeaker system.

Leak "Varislope" Stereo Pre-amplifier

Valves: four EF86 or Z729 or 6267. Total harmonic distortion: less than 0.1% for 1.25V output. Hum and noise: 60db below full output. Dimensions: 10" x 3" x 6" deep (front panel 11" W). Weight: 6lb.

Leak "Stereo 20" Main Amplifier

Each channel is identical in gain within 0.5db and the characteristics of each channel are as follows: Power output: 12 watts rms. maximum. Total harmonic distortion: 0.1% for 10 watts output (± 1db) at 1,000 c/s. Hum and noise: 80db ± 3db below 10 watts. Sensitivity: an input of 125mV gives 10 watts output. Frequency response: ± 0.5db, 20-20,000 c/s. Damping factor: 25.
Loudspeaker impedances: between 3 ohms and 20 ohms. Power supply: 200-250V, 50-110 c/s, or 100-125V, 50-100 c/s. Consumption: 130 watts. 18

Leak "Stereo 60" Main Amplifier

Valves: three ECC83 (B339 or 12AX7), four EL34 (KT66 or 5881), one GZ34 (5AR4). Power output: 60 watts rms max. (30 watts each channel). Total harmonic distortion: 0.1% for 30 watts rms output per channel at 1,000 c/s. Hum and noise: 80db below max. output with source impedance of 25,000 ohms. Sensitivity: 120mV input gives max. output. Frequency response: ± 0.5db, 20 to 20,000 c/s. Damping factor: 25, measured at 1,000 c/s. Loudspeaker impedances: any between 3 and 20 ohms.
Power supply: 200-250V, 50-100 c/s or (alternative model) 100-125V, 50-100 c/s. Dimensions: 10"w x 13"d x 6"h. Weight: 27 lb.

Pamphonic 3001 Stereo Amplifier

Valves: one EF86, one ECC81, two ECL82, (per channel). Power output: 7.5 watts (per channel). Distortion: 0.5% at 6 watts. Hum and noise: —60db. Power supply: 100-150V, 200-250V, 50-60 c/s. Dimensions: 13"w x 10"d x 4"h. Weight: 18 lb.

Pye Mozart HF10M Amplifier

Valves: three. Output: 10 watts. Distortion: 0.3% at 9 watts. Hum: -75db. Maximum sensitivity: 10 mV for 10 watts at 1,000 c/s. Frequency response: ±3db, 3-50,000 c/s. Power supply: 110-120V, or 210-250V AC. Dimensions: 10"w x 5"d x 3"h. Weight: 8lb. (9 lb. in metal case). Also available in chassis form.

Pye HFS20M

Valves: two ECC83, two EL34. Power output: 10 watts per channel. Total harmonic distortion: 0.3% at 9 watts. Hum and noise: 55-60db. Frequency response: ± 1.5db, 20-20,000 c/s. Power supply: 200-225V, 50 c/s, 110-120V, 60 c/s. Dimensions: 10"w x 11"d x 3"h. Also available in chassis form.

Rogers RD Cadet Control Unit

Valve: ECC83 twin-triode. Frequency response: (controls level) ±1db. 40-15,000 c/s. Dimensions: 8"w x 5"d x 2"h. Weight: 3lb.

Rogers R.D. Cadet Amplifier Mk.ll

Valves: E281,two ECL86. Power output: 7 watts. Harmonic distortion: 0.25% for 7 watts. Hum and noise: 75db below 7 watts. Power supply: 200-250V AC. Dimensions: 12" x 4" x 4". Weight: 10lb.

Rogers R.D. Junior Mk.lll Stereo Control Unit

Valves: two EF86, two ECC83. Dimensions: 11" x 7" x 5". Weight: 8 lb.

Rogers RD Junior Stereo Amplifier

Valves: four EL84, two ECC83, two GZ34. Power output: 12 watts per channel (15 watts peak). Total harmonic distortion: 0.2% at 12 watts output, 1,000 c/s. Hum and noise: -85db below 12 watts. Sensitivity: 750mV rms. for 12 watts. Frequency response: ± 0.25db, 20-20,000 c/s. Damping factor: 20. Loudspeaker impedance: 4, 8 or 16 ohms. Power supply: 200-230-250V 50 c/s or 110-115-125V 50-60 c/s. Consumption: 125 watts. Dimensions: 14" x 8" x 5". Weight: 33 lb.

Rogers HG88 Mk.ll Stereo Amplifier

Valves: two EF86, two ECC83, four ECL86, GZ34. Power output: 12 watts rms per channel (14 watts peak). Total harmonic distortion: 0.25% for 12 watts. Hum and noise: 80db below 12 watts. Frequency response: ± 1db, 30-20,000 c/s. Power supply: 110-250V AC. Consumption: 95 watts. Dimensions: (in teak case) 15" x 10" x 7". Weight: 21lb. Also available in chassis form. Dimensions: 14" x 10" x 5". Weight :23 lb.

Rogers Master Stereo Control Unit

Valves: two EF86, four ECC83. Frequency response: ± 1db 20-20,000 c/s. Dimensions: 14" x 6" x 5". Weight: 10 lb.
-

Es war eine erstaunliche Auswahl an englischen Geräten.

-

 

-

- Werbung Dezent -
Zurück zur Startseite © 2007/2024 - Deutsches Hifi-Museum - Copyright by Dipl.-Ing. Gert Redlich Filzbaden - DSGVO - Privatsphäre - Zum Telefon der Redaktion - Zum Flohmarkt
Bitte einfach nur lächeln: Diese Seiten sind garantiert RDE / IPW zertifiziert und für Leser von 5 bis 108 Jahren freigegeben - Tag und Nacht und kostenlos natürlich.

Privatsphäre : Auf unseren Seiten werden keine Informationen an google, twitter, facebook oder andere US-Konzerne weitergegeben.